Shaniwar Peth, Pune, Maharashtra
GST No. 27AAECV6436E1Z9
Call 08046040537 68% Response Rate
Shape | Rectangular |
Material | Nanocrystalline and Amorphous ribbon |
Thickness | 20mm |
Color | Silver |
Surface Finish | Polished |
Country of Origin | Made in India |
Usage: Suitable for use in Electric Vehicle Chargers / Magnetic Analyzers, Special Applications
Blocks of Special Geometry used in Axial Flux Stator/Rotor Cores.
Suitable for Both, fundamental Frequency & High Frequency Applications.
Rate: Rs.3000/- per kg
Material: Nano crystalline / Amorphous ribbons
Shape: Rectangular / Square / Customized
Material Thickness: 25 micron (±5 micron)
Density : 7.25 Kg/cm²
Curie Temperature: 560°C
Wattloss: 0.5 Tesla @ 20KHz ≤ 30 Watts/Kg
Remanence: 20 KHz ≤ 0.3 Tesla
Surface finish: Smooth
Country of origin: Made in India
Advantages (Nanocrystalline Blocks): High Permeability, High AL-value/Inductance, Lower Power Loss, Low Remenance, Low Coercivity
Advantages (Amorphous Blocks): Stable operation/Performance over wide Frequency range, Better Performance at Higher Frequencies
View Complete details
Usage/Application | High Metering Accuracy Current Transformers |
Transformer Type | Nanocrystalline Cores |
Thickness | As per Requirement |
Core Type | Toroidal & Rectangular |
Phase | Three Phase |
Shape | Tape Wound |
Technique | Tape Wound Cores in Toroidal and Rectangular Shapes |
Material | Nanocrystalline |
Frequency | 50Hz |
Capacity | Upto 765kV Class |
Temperature | 130 degrees C |
Sizes | 1200mm max OD |
Saturation Flux Density | Upto 1.25Tesla |
Finishing | Insulated Tape Finish |
Application : Transmission / Generation / Distribution - Metering cores used in current transformers
Rate : Rs.1200/- per kg
Shape : Round / Rectangular / Oval /Special Geometries
Material : Nano crystalline ribbon
Frequency : 50 Hz / 60 Hz / as per design
Sizes : OD : from 10 mm to 1200 mm
ID : min 05 mm
HT : min 05 mm
Capacity : Upto 765 KV class
Country of origin : Made in India.
Finishing: Since nano crystalline material is very thin & brittle, cores can’t be supplied in bare form but needs good encapsulation which is available in following options:
i) Stainless steel / Aluminum (non magnetic) casing
ii) Insulating board/PCB casing
iii) Plastic casing (for large quantities)
iv) Araldite & crape paper covering
For final core dimensions thickness of canopy should be considered, following is the general formula for same
Final ID : ID of bare core -5 MM (±2 mm)
Final OD : OD of bare core + 5 MM (±2 mm)
Final HT : Ht of bare core + 5 MM (± 2 mm)
View Complete details
Minimum Order Quantity: 10 Piece
Usage/Application | Current Transformer |
Transformer Type | Current Transformer |
Thickness | As per customer requirement |
Phase | Three Phase |
Core Type | Ring Core Type |
Shape | Round |
Technique | Toroidal Winding |
Material | Nanocrystalline |
Frequency | 50Hz |
Rate: Rs.1000/- to 10000/- per pc
Usage: CT & Toroidal transformers
Material: Nano crystalline ribbon / CRGO of various grade
Specification: 0.2S class copper wound metering cores upto 765 KV class
PS class copper wound metering cores
Additional Information:
View Complete details
Usage/Application | Distribution Transformer |
Thickness | 35 microns |
Core Type | Ribbon |
Grade | Vikano Super 300 |
Country of Origin | Made in India |
Nano crystalline ribbons are fruit of complex engineering techniques. Basically a suitable alloy is made with sophisticated metallurgy followed by rapid quenching with metal spinning technology with cooling rate more than one million degree /sec
Rate : Rs.650/- to Rs.900/- per kg
Usage / Application : Metering CT cores/CBCT cores/Blocks/Welding cores/High frequency cores/ Metering cores
Country of origin: Made in India
Material Properties :
Density |
7.2 gms/cc |
Filling Factor |
78%-80% |
Permeability |
250000 to 400000 |
Saturation Induction |
1.2 T |
Curie Temperature |
560 deg C |
Max Operating Temperature |
150 deg C |
Thickness (mm) |
0.025 ∼0.035 |
Available width |
5 mm to 50 mm |
View Complete details
Model Name/Number | Nano crystalline ribbon |
Usage/Application | Transmission |
Brand | Vikarsh Nano Technology And Alloys Private Limited |
Voltage | 765 KV class |
Power Supply | 765 KV class |
Dimension | OD : from 10 mm to 1200 mm |
Country of Origin | Made in India |
Finishing: Since nano crystalline material is very thin & brittle, cores can’t be supplied in bare form but needs good encapsulation which is available in following options:
i) Stainless steel / Aluminum (non magnetic) casing
ii) Insulating board/PCB casing
iii) Plastic casing (for large quantities)
iv) Araldite & crape paper covering
For final core dimensions thickness of canopy should be considered, following is the general formula for same
Final ID : ID of bare core -5 MM (±2 mm)
Final OD : OD of bare core + 5 MM (±2 mm)
Final HT : Ht of bare core + 5 MM (± 2 mm)
View Complete details
Material | Nano crystalline |
Usage/Application | Energy meters, Current transformer, Etc |
Core Type | Ring Core Type |
Technique | High permeability |
Size | Upto 1000 mm OD |
Usage/ Application : 1. LT Metering applications, Digital Current Meters.
2. CBCTs Ground Fault Interruptors/Earth Leakage Circuit Breakers
3. Common Mode Chokes, EMI Filters.
4. DC Immune Dual Cores/Current Sensors/Hall Effect Sensors
Core size : Min.ID : 8 MM
Max OD : 65 MM
Max HT : 30 MM
Rate: Rs.10/- to Rs.50/- per pc (as per required size)
Shape: Round
Material: Nano crystalline steel / Amorphous steel as per requirement
Frequency: Upto 100 KHz
Country of origin : Made in India.
Available Finishing: 1) PBT/PET/Nylon Canopies (Standard Sizes Available)
2) UL / Non UL epoxy Powder Coated Cores (For Non-Standard Sizes)
Dimensions : For core sizes in PBT/PET/Nylon canopies, please refer below list
For cores in powder coating. Min Bare Core ID:08mm can be accepted upto 35 mm OD
View Complete details
Nano crystalline ribbons are fruit of complex engineering techniques. Basically a suitable alloy is made with sophisticated metallurgy followed by rapid quenching with metal spinning technology with cooling rate more than one million degree /sec
Rate : Rs.650/- to Rs.900/- per kg
Usage / Application : Metering CT cores/CBCT cores/Blocks/Welding cores/High frequency cores/ Metering cores
Country of origin: Made in India
Material Properties :
Density |
7.2 gms/cc |
Filling Factor |
78%-80% |
Permeability |
250000 to 400000 |
Saturation Induction |
1.2 T |
Curie Temperature |
560 deg C |
Max Operating Temperature |
150 deg C |
Thickness (mm) |
0.025 ∼0.035 |
Available width |
5 mm to 50 mm |
View Complete details
Nano crystalline ribbons are fruit of complex engineering techniques. Basically a suitable alloy is made with sophisticated metallurgy followed by rapid quenching with metal spinning technology with cooling rate more than one million degree /sec
Rate : Rs.650/- to Rs.900/- per kg
Usage / Application : Metering CT cores/CBCT cores/Blocks/Welding cores/High frequency cores/ Metering cores
Country of origin: Made in India
Material Properties :
Density |
7.2 gms/cc |
Filling Factor |
78%-80% |
Permeability |
250000 to 400000 |
Saturation Induction |
1.2 T |
Curie Temperature |
560 deg C |
Max Operating Temperature |
150 deg C |
Thickness (mm) |
0.025 ∼0.035 |
Available width |
5 mm to 50 mm |
View Complete details
Nano crystalline ribbons are fruit of complex engineering techniques. Basically a suitable alloy is made with sophisticated metallurgy followed by rapid quenching with metal spinning technology with cooling rate more than one million degree /sec
Rate : Rs.650/- to Rs.900/- per kg
Usage / Application : Metering CT cores/CBCT cores/Blocks/Welding cores/High frequency cores/ Metering cores
Country of origin: Made in India
Material Properties :
Density |
7.2 gms/cc |
Filling Factor |
78%-80% |
Permeability |
250000 to 400000 |
Saturation Induction |
1.2 T |
Curie Temperature |
560 deg C |
Max Operating Temperature |
150 deg C |
Thickness (mm) |
0.025 ∼0.035 |
Available width |
5 mm to 50 mm |
View Complete details
Nano crystalline ribbons are fruit of complex engineering techniques. Basically a suitable alloy is made with sophisticated metallurgy followed by rapid quenching with metal spinning technology with cooling rate more than one million degree /sec
Rate : Rs.650/- to Rs.900/- per kg
Usage / Application : Metering CT cores/CBCT cores/Blocks/Welding cores/High frequency cores/ Metering cores
Country of origin: Made in India
Material Properties :
Density |
7.2 gms/cc |
Filling Factor |
78%-80% |
Permeability |
250000 to 400000 |
Saturation Induction |
1.2 T |
Curie Temperature |
560 deg C |
Max Operating Temperature |
150 deg C |
Thickness (mm) |
0.025 ∼0.035 |
Available width |
5 mm to 50 mm |
View Complete details
Nano crystalline ribbons are fruit of complex engineering techniques. Basically a suitable alloy is made with sophisticated metallurgy followed by rapid quenching with metal spinning technology with cooling rate more than one million degree /sec
Rate : Rs.650/- to Rs.900/- per kg
Usage / Application : Metering CT cores/CBCT cores/Blocks/Welding cores/High frequency cores/ Metering cores
Country of origin: Made in India
Material Properties :
Density |
7.2 gms/cc |
Filling Factor |
78%-80% |
Permeability |
250000 to 400000 |
Saturation Induction |
1.2 T |
Curie Temperature |
560 deg C |
Max Operating Temperature |
150 deg C |
Thickness (mm) |
0.025 ∼0.035 |
Available width |
5 mm to 50 mm |
View Complete details